1. Highlight the printer you want to use, and click button in the [Current MediaA paper or other substrate that the printer creates images on. and Page Size] area. This opens the "Change Media and Page Size" dialog (Figure 1).
2. In the Placement field, use the drop-down box to select your placement strategy.
3. Click button to modify any options for the [Placement Strategy]. This opens the "Placement Strategy" dialog (Figure 2).
4. Make your changes, and click [OK].

Click button in the [Placement] field and set your Placement Strategy Options (Figure 2 &3).

 

NOTE: Depending on your Placement Strategy, these options may or may not be available.

 

[General] Tab

The [General] tab (Figure 2) includes the following options:

• Print TriggeringThe mechanism by which RIP-Queue determines when jobs can be printed. Manual print triggering is controlled by the Print Now button. Automatic print triggering is controlled by a time-out value or an area percentage value of media usage. - You can set your Print Triggering options to begin printing once certain conditions are met. [Time Based Start] requires that a certain amount of time pass before printing. [Area Based Start] requires that a certain amount of media be used before printing. [Automatically Start Printing] begins printing immediately after processing. If no [Print Triggering] option is selected, printing will only begin when the [Print Now] button is clicked.

• Justification - This option determines where the image is placed on the media. If you are using a strategy that prints multiple images at the same time, the justification applies to the group of images.
• Offset - This option adds extra white space to the left or top of an image. If you are using a strategy that prints multiple images at a time, the offset applies to the group of images.
• Printing Gutter - This option determines the size and placement of the gutter. Select Left, Right, or both Left and Right gutters and adjust the gutter size using the up and down arrows.
• Flip every other tile - This option flips every other tile in an image.

 

[Options] Tab

The [Options] Tab (Figure 3) includes the following options:

• Space Between Copies - This option determines the amount of white space placed (Horizontal and Vertical) between the copy of images.

• Space Between Image and Cutter Mark - This option determines the amount of white space placed between the image and the cutter mark.
• Cutter Mark Darkness - This option determines the darkness of your cutter marks. The lower the number is the lighter setting.
• Grouping - This option determines how RIP-Queue orders the tiles or copies of a job when printing. You can select [By Tiles] or [By Copies]. If you select [By Tiles], all the tiles of an image will be printed before the next copy of the image is begun. If you select [By Copies], each copy of the image will be printed before the next tile is begun. You can also select to [Rearrange Tiles to Conserve Media].
• Horizontal Copying - This option places tiles or copies of a job side-by-side across the page, instead of placing each tile or copy on its own row.
• Vertical Copying - This option places tiles or copies of a job side-by-side across the page, instead of placing each tile or copy on its own column.
• Print Multiple Rows at a Time - This option sends multiple rows to the printer at the same time. The rows are printed as one group when you set a placement as [Print Jobs Individually].
• Print all rows at a time - This option sends all rows to the printer at the same time. The rows are printed as one group when you set a placement as [Group Jobs Together].
• BestFit - This option automatically adjusts the layout of your jobs to ensure that the most media is used when you set a placement as [Conserve Media]. The [Allow Rotate] option allows RIP-Queue to automatically rotate Square ResolutionThe number of dots available to represent graphic detail in a given area. On a computer screen, resolution is usually measured in pixels per inch (ppi). On a printer, the resolution is measured in dots per inch, or dpi. Halftone resolution measurements are in lines per inch, or LPI. See also Screen Ruling. images for better fit.
• Percent to cache before printing - This option allows you to set when the processed information is sent to the printer. When it is set to 0 %, information is sent to the printer as fast as it is processed. When it is set to 100 %t, information is not sent to the printer until the entire print is finished processing.
• Size of Cutter Mark – This option allows you to determine how much the thickness of the cutter line. Default setting is [2.95mm (0.118 inch)]. If you want to put the cutter mark on the edge of an image, check a box of [Image Width] option.

• Horizontal/Vertical Cutter Marks – These options allow you to set single line or double lines of the cutter mark that will be placed on your image. Check the box of [Single] or [Double] you desire.

 

NOTE: A Square Resolution is a resolution that has the same vertical and horizontal values. For example, 720 X 720 is a Square Resolution. 360 X 720 is an example of a non-Square Resolution.

You can choose to use any of the following [Placement (Nesting) Strategies] from a drop down menu (Figure 4):

• Conserve Media - This method uses a row-based system to organize images and save as much media as possible. A row is determined by the height of the largest available image. All other images in a row can be equal too, but not greater than this image. Every time a job enters RIP-Queue, the entire nest is re-arranged to better fit the new job. This method will not rotate images by default. Use [Conserve Media] if you want to save media and do not need to print jobs on a strict priority basis.

NOTE: [Conserve Media] has three different methods: Conserve Media with BestFit turned off, Conserve Media with BestFit turned on and Allow Rotate off, and Conserve Media with both BestFit and Allow Rotate turned on. Use the one that gives the best results.

• Group Jobs Together - This method places jobs side-by-side to save more media, but does not rotate or re-arrange the order of the jobs. Use [Group Jobs Together] if you want to save media and need to print on a strict priority basis.
• Print Jobs Individually - This method prints each job as it is submitted. Use [Print Jobs Individually] if you do not need to save media and need to print jobs on a strict priority basis.
• Fotoba, Dicus or Flexa Cutter Marks - This method prints your images with Fotoba, Dicus, or Flexa cutter marks. This will automatically conserve as much media as possible, but it also creates extra space around each image for the cutter marks. Use this option only if you need to print your images with Fotoba, Dicus, or Flexa cutter marks.

This option is only available for specific printers. This option allows you to see and interact with live bidirectional printer status such as Ink Volumes and loaded Media (Figure 5).